Welcome to 310 Motor repository
For Jetson NANO
Drive motor and read encoder-IIC
1.1 Explanation
Please read 《0. Motor introduction and usage》first to understand the motor parameters, wiring method, and power supply voltage you are currently using. To avoid improper operation and damage to the driver board or motor.
I2C and serial communication cannot be shared, only one can be selected.
Hardware wiring:
| Motor | 4-channel motor drive board(Motor) |
|---|---|
| M2 | M- |
| V | 3V3 |
| A | H1A |
| B | H1B |
| G | GND |
| M1 | M+ |
| 4-channel motor drive board | Jetson NANO B01（Physical Pins） |
|---|---|
| SDA | 3 |
| SCL | 5 |
| GND | 6 |
| 5V | 4 |
1.2 Instructions
Use file transfer software, such as WinSCP. You need to search and download the software yourself.
Transfer the py file to the root directory of the motherboard through the software, then open the terminal and run the command.
sudo python3 ~/IIC.py
If the terminal prompts an error message indicating that the smbus module is missing.
Use the following command to install this module and try running again.
xxxxxxxxxxsudo apt updatesudo apt install python3-smbus
1.3 Code analysis
xUPLOAD_DATA = 1 #1:接收总的编码器数据 2:接收实时的编码器 #1: Receive total encoder data 2: Receive real-time encoder
MOTOR_TYPE = 1 #1:520电机 2:310电机 3:测速码盘TT电机 4:TT直流减速电机 5:L型520电机 #1:520 motor 2:310 motor 3:speed code disc TT motor 4:TT DC reduction motor 5:L type 520 motorUPLOAD_DATA: used to set the data of the motor encoder. Set 1 to the total number of encoder pulses and 2 to the real-time pulse data of 10ms.
MOTOR_TYPE: used to set the type of motor used. Just modify the corresponding numbers according to the comments according to the motor you are currently using. You don’t need to modify the rest of the code.
If you need to drive the motor and observe the data, just modify the two numbers at the beginning of the program. No changes are required to the rest of the code.
xxxxxxxxxxdef set_motor_parameter():
if MOTOR_TYPE == 1: set_motor_type(1) # 配置电机类型 time.sleep(0.1) set_pluse_phase(30) # 配置减速比，查电机手册得出 time.sleep(0.1) set_pluse_line(11) # 配置磁环线，查电机手册得出 time.sleep(0.1) set_wheel_dis(67.00) # 配置轮子直径，测量得出 time.sleep(0.1) set_motor_deadzone(1900) # 配置电机死区，实验得出 time.sleep(0.1)
elif MOTOR_TYPE == 2: set_motor_type(2) time.sleep(0.1) set_pluse_phase(20) time.sleep(0.1) set_pluse_line(13) time.sleep(0.1) set_wheel_dis(48.00) time.sleep(0.1) set_motor_deadzone(1600) time.sleep(0.1)
elif MOTOR_TYPE == 3: set_motor_type(3) time.sleep(0.1) set_pluse_phase(45) time.sleep(0.1) set_pluse_line(13) time.sleep(0.1) set_wheel_dis(68.00) time.sleep(0.1) set_motor_deadzone(1250) time.sleep(0.1)
elif MOTOR_TYPE == 4: set_motor_type(4) time.sleep(0.1) set_pluse_phase(48) time.sleep(0.1) set_motor_deadzone(1000) time.sleep(0.1)
elif MOTOR_TYPE == 5: set_motor_type(1) time.sleep(0.1) set_pluse_phase(40) time.sleep(0.1) set_pluse_line(11) time.sleep(0.1) set_wheel_dis(67.00) time.sleep(0.1) set_motor_deadzone(1900) time.sleep(0.1)This is used to store the parameters of the Yahboom motor. By modifying the MOTOR_TYPE parameter above, one-click configuration can be achieved.
In normally, do not modify the code here when using the Yahboom motor.
If you are using your own motor, or if a certain data needs to be modified according to your needs, you can check the course《1.2 Control command》 to understand the specific meaning of each command.
xxxxxxxxxxif __name__ == "__main__": try: t = 0 print("please wait...") set_motor_parameter() # 设置自己的电机参数 Set your own motor parameters
while True: t += 10 M1 = t M2 = t M3 = t M4 = t
if MOTOR_TYPE == 4: control_pwm(M1*2, M2*2, M3*2, M4*2) else: control_speed(M1, M2, M3, M4)#直接发送命令控制电机 Send commands directly to control the motor if t> 1000 or t < -1000: t = 0
if UPLOAD_DATA == 1: now_string = read_all_encoder() # 读取累计编码器数据 Read the accumulated encoder data print(now_string) elif UPLOAD_DATA == 2: offset_string = read_10_encoder() # 读取实时编码器数据 Read real-time encoder data print(offset_string) time.sleep(0.1)
In the main program loop, the speed of the four motors will be slowly increased from 0 to 1000. If the motor type is 4, that is, the motor without encoder, the PWM of the motor is directly controlled.
At the same time, the data sent by the driver board is read and printed out.
xxxxxxxxxx# 读取编码器数据 Read encoder datadef read_10_encoder(): global encoder_offset formatted_values = [] for i in range(4): reg = READ_TEN_M1_ENCODER_REG + i buf = i2c_read(MOTOR_MODEL_ADDR, reg, 2) encoder_offset[i] = (buf[0] << 8) | buf[1] if encoder_offset[i] & 0x8000: # 检查最高位（符号位）是否为 1 Check if the highest bit (sign bit) is 1 encoder_offset[i] -= 0x10000 # 将其转为负数 Turn it into a negative number formatted_values.append("M{}:{}".format(i + 1, encoder_offset[i])) return ", ".join(formatted_values)
def read_all_encoder(): global encoder_now formatted_values = [] for i in range(4): high_reg = READ_ALLHIGH_M1_REG + (i * 2) low_reg = READ_ALLLOW_M1_REG + (i * 2) high_buf = i2c_read(MOTOR_MODEL_ADDR, high_reg, 2) low_buf = i2c_read(MOTOR_MODEL_ADDR, low_reg, 2) high_val = high_buf[0] <<8 | high_buf[1] low_val = low_buf[0] <<8 | low_buf[1] encoder_val = (high_val << 16) | low_val # 处理符号扩展，假设 32 位有符号整数 Handles sign extension, assuming 32-bit signed integers if encoder_val >= 0x80000000: # 如果大于 2^31，说明应该是负数 If it is greater than 2^31, it should be a negative number encoder_val -= 0x100000000 # 将其转为负数 Turn it into a negative number encoder_now[i] = encoder_val formatted_values.append("M{}:{}".format(i + 1, encoder_now[i])) return ", ".join(formatted_values)
After getting the data from the driver board, it is shifted, and the shift is required to get the correct data.
1.4 Experimental phenomenon
After the wiring is correct, place the program in the root directory, and then run the command sudo python3 ~/IIC.py. You can see that the motor will gradually speed up, then stop, and repeat.
At the same time, you can see the printed motor value in the terminal constantly changing.
