Welcome to Wheeled Chassis Kit repository
For PICO2
Drive motor and read encoder-USART
1.1 Explanation
Please read 《0. Motor introduction and usage》first to understand the motor parameters, wiring method, and power supply voltage you are currently using. To avoid improper operation and damage to the driver board or motor.
I2C and serial communication cannot be shared, only one can be selected.
Hardware wiring:
| Motor | 4-channel motor drive board(Motor) |
|---|---|
| M2 | M- |
| V | 3V3 |
| A | H1A |
| B | H1B |
| G | GND |
| M1 | M+ |
| 4-channel motor drive board | Pico2 |
|---|---|
| RX2 | GP0 |
| TX2 | GP1 |
| GND | GND |
| 5V | 3V3 |
1.2 Instructions
Open the code using Thonny software, connect to the Raspberry Pi pico2, and click the stop button on the far right of the upper toolbar.
Then, you can see the information of the current firmware in pico2 pop up in the message bar at the bottom, which means that the software has recognized the serial port.
If the message bar here shows that the serial port cannot be recognized, you need to refer to the firmware flashing tutorial and flash the firmware to the motherboard so that the serial port can be recognized.
After successfully identifying the serial port and printing the firmware information, click the green button to start running the script.
1.3 Code analysis
xUPLOAD_DATA = 3 #0:不接受数据 1:接收总的编码器数据 2:接收实时的编码器 3:接收电机当前速度 mm/s #0: Do not receive data 1: Receive total encoder data 2: Receive real-time encoder 3: Receive current motor speed mm/s
MOTOR_TYPE = 1 #1:520电机 2:310电机 3:测速码盘TT电机 4:TT直流减速电机 5:L型520电机 #1:520 motor 2:310 motor 3:speed code disc TT motor 4:TT DC reduction motor 5:L type 520 motor
UPLOAD_DATA: used to set the data of the motor encoder. Set 1 to the total number of encoder pulses and 2 to the real-time pulse data of 10ms.
MOTOR_TYPE: used to set the type of motor used. Just modify the corresponding numbers according to the comments according to the motor you are currently using. You don’t need to modify the rest of the code.
If you need to drive the motor and observe the data, just modify the two numbers at the beginning of the program. No changes are required to the rest of the code.
xxxxxxxxxxdef set_motor_parameter():
if MOTOR_TYPE == 1: set_motor_type(1) # 配置电机类型 time.sleep(0.1) set_pluse_phase(30) # 配置减速比，查电机手册得出 time.sleep(0.1) set_pluse_line(11) # 配置磁环线，查电机手册得出 time.sleep(0.1) set_wheel_dis(67.00) # 配置轮子直径，测量得出 time.sleep(0.1) set_motor_deadzone(1600) # 配置电机死区，实验得出 time.sleep(0.1)
elif MOTOR_TYPE == 2: set_motor_type(2) time.sleep(0.1) set_pluse_phase(20) time.sleep(0.1) set_pluse_line(13) time.sleep(0.1) set_wheel_dis(48.00) time.sleep(0.1) set_motor_deadzone(1200) time.sleep(0.1)
elif MOTOR_TYPE == 3: set_motor_type(3) time.sleep(0.1) set_pluse_phase(45) time.sleep(0.1) set_pluse_line(13) time.sleep(0.1) set_wheel_dis(68.00) time.sleep(0.1) set_motor_deadzone(1250) time.sleep(0.1)
elif MOTOR_TYPE == 4: set_motor_type(4) time.sleep(0.1) set_pluse_phase(48) time.sleep(0.1) set_motor_deadzone(1000) time.sleep(0.1)
elif MOTOR_TYPE == 5: set_motor_type(1) time.sleep(0.1) set_pluse_phase(40) time.sleep(0.1) set_pluse_line(11) time.sleep(0.1) set_wheel_dis(67.00) time.sleep(0.1) set_motor_deadzone(1600) time.sleep(0.1)This is used to store the parameters of the Yahboom motor. By modifying the MOTOR_TYPE parameter above, one-click configuration can be achieved.
In normally, do not modify the code here when using the Yahboom motor.
If you are using your own motor, or if a certain data needs to be modified according to your needs, you can check the course《1.2 Control command》 to understand the specific meaning of each command.
xxxxxxxxxxif __name__ == "__main__": try: t = 0 print("please wait...") send_upload_command(UPLOAD_DATA)#给电机模块发送需要上报的数据 Send the data that needs to be reported to the motor module time.sleep(0.1) set_motor_parameter()#设计电机参数 Design motor parameters
while True: received_message = receive_data() # 接收消息 Receiving Messages if received_message: # 如果有数据返回 If there is data returned parsed = parse_data(received_message) # 解析数据 Parsing the data if parsed: print(parsed) # 打印解析后的数据 Print the parsed data
t += 10 M1 = t M2 = t M3 = t M4 = t if MOTOR_TYPE == 4: control_pwm(M1*2, M2*2, M3*2, M4*2) else: control_speed(M1, M2, M3, M4)#直接发送命令控制电机 Send commands directly to control the motor
if t> 1000 or t < -1000: t = 0
time.sleep(0.1)
In the loop program, the speed of the four motors will be slowly increased from 0 to 1000. If the motor type is 4, that is, the motor without encoder, the motor's PWM is directly controlled.
At the same time, the data sent by the driver board is read and printed out at the same time.
xxxxxxxxxx# 接收数据 Receiving Datadef receive_data(): global recv_buffer if uart.any() > 0: # 检查串口缓冲区是否有数据 Check if there is data in the serial port buffer recv_buffer += uart.read(uart.any()).decode() # 读取并解码数据 Read and decode data # 按结束符 "#" 分割消息 Split the message by the ending character "#" messages = recv_buffer.split("#") recv_buffer = messages[-1] if len(messages) > 1: return messages[0] + "#" #返回一条完整的消息 Return a complete message return None
# 解析接收到的数据 Parsing received datadef parse_data(data): data = data.strip() # 去掉两端的空格或换行符 Remove spaces or line breaks at both ends
if data.startswith("$MAll:"): values_str = data[6:-1] # 去除 "$MAll:" 和 "#" Remove "$MAll:" and "#" values = list(map(int, values_str.split(','))) # 分割并转换为整数 Split and convert to integer parsed = ', '.join([f"M{i+1}:{value}" for i, value in enumerate(values)]) return parsed elif data.startswith("$MTEP:"): values_str = data[6:-1] values = list(map(int, values_str.split(','))) parsed = ', '.join([f"M{i+1}:{value}" for i